Filter
MS scaled x

MS-907 Two-Part Epoxy Adhesive

For bonding metals, glass, ceramics, plastics, wood, rubber, fabrics and concrete.  Miller-Stephenson’s Epoxy 907 Adhesive System is a two-part, equal volume, room temperature curing system particularly useful for general purpose bonding.  Fast set-up time.  Perfect for in-plant and field use.  Develops bond strength up to 3,000 psi.

Category: Tags: , , ,

MS-907 Two-Part Epoxy Adhesive system kit is a two-part, equal volume, room temperature curing system particularly useful for general purpose bonding. Fast setup time. Perfect for in-plant and field use. Develops bond strength to 3,000 psi. NSN 8040-00-144-9729.

Perfect for in-plant and field use. Develops superior bond strength and provides adhesion to a variety of substrates. Application: Metals, Glass, Ceramics, Plastics, Wood, Rubber, Fabrics, Concrete Base: Epoxy Resin Color: Part A is blue. Part B is beige. When thoroughly mixed, the resultant color is pale gray Container Size: 3.

7 oz. Container Type: Tubes Cure Time: 24 hours at 77 F (25 C), or 2 hours at 140 F (60 C), or one hour at 180 F (82 C) Mixing Ratio: Equal parts by volume Special Features: Good adhesion to a wide variety of surfaces which have not been specially cleaned.

Proportioning of Parts A and B not critical. Definite color change during mixing. Temperature Range: Up to 180 F (82 C) Viscosity: Approximately 120, 000 cps, thixotropic Work Life: 20 minutes at 77 F (25 C).

The recommendation made here with and the information set forth with respect to the performance or use of our products are believed, but not warranted to be accurate. The products discussed are sold without warranty, as to fitness or performance, express or implied and upon condition that purchasers shall make their own test to determine suitability of such products for their particular purposes. Likewise, statements concerning the possible uses of our products are not intended as recommendations to use our products in the infringement of any patent.

BONDING STRENGTHTo 3,000 PSI
 

FORM

A two-part paste adhesive packaged in equal volume tubes.
 

COLOR

 

Part A is blue.  Part B is beige.  When thoroughly mixed, the result is light blue.
VISCOSITYApproximately 120,000 cP, thixotropic.
MIX RATIOEqual parts by volume.
POT LIFE20 minutes at 77˚F, 200 grams
CURE TIME24 hours at 77˚F, or 2 hours at 140˚F, or

1 hour at 180˚F. Do not attempt to cure below 60˚F.

SERVICE TEMPERATURE-50˚ to 180˚F
SHELF LIFEMore than 1 year at 75˚F.
SPECIAL PROPERTIESGood adhesion to wide variety of surfaces.

Color-coded for proper mixing.

The recommendation made here with and the information set forth with respect to the performance or use of our products are believed, but not warranted to be accurate. The products discussed are sold without warranty, as to fitness or performance, express or implied and upon condition that purchasers shall make their own test to determine suitability of such products for their particular purposes. Likewise, statements concerning the possible uses of our products are not intended as recommendations to use our products in the infringement of any patent.

MS-907

MS-907 TDS

Download File

DIRECTIONS:

  • CLEAN SURFACES Surfaces to be bonded must be clean, dry and free of oil,grease or wax.  Roughen nonporous surfaces with sandpaper or emery paper for hard materials.
  • MIX EQUAL PARTS Squeeze a length from tube A on a clean, dry, flat disposable surface.  Use uniform pressure for even bead.  Parallel to tube A, run an equal length bead from tube B.longer.  When properly mixed, the adhesive is light blue
  • APPLY TO BOTH SURFACES Cover entire area evenly.
  • JOIN PARTS TOGETHER FIRMLY Squeeze out excess adhesive to form thin glue line.  A larger area will require more pressure.  Hold parts together with
    clamps, weights or tape
  • MIX THOROUGHLY Important! Mix the two beads together for 3 minutes
  • REMOVE EXCESS ADHESIVE PROMPTLY Before adhesive hardens,scrape with putty knife.  Clean with lacquer thinner, acetone or turpentine.  Once cured, adhesive may be removed by sanding.

The recommendation made here with and the information set forth with respect to the performance or use of our products are believed, but not warranted to be accurate. The products discussed are sold without warranty, as to fitness or performance, express or implied and upon condition that purchasers shall make their own test to determine suitability of such products for their particular purposes. Likewise, statements concerning the possible uses of our products are not intended as recommendations to use our products in the infringement of any patent.