MS-907 Plus | Two-Part Epoxy Resin Kit System
Ideal For Bonding; Fast Set-Up Time; Room Temperature Curing System
MS-907 Plus is a multi-purpose Epoxy resin kit and repair adhesive system. It’s specially formulated, a non-sag property is ideal for bonding most materials, such as metal, glass, ceramics, plastics, wood, rubber, and concrete. MS-907 Plus is a two-part, equal volume, room temperature curing system. Fast set-up time. Perfect for in-plant and field use. It has an application temperature range between 40°F/4°C and 100°F/38°C.
Epoxy Resin Kit Advantages:
- Rapid initial 3-hour cure at room temperature
- Moisture insensitive system and may be used on damp surfaces
- Non-sag patching material for cracks
- Ideal for overhead and vertical repairs
- Ratio & Cure:
- Part A (Resin) White, Part B (Hardener) Dark Gray
- Mixed: Concrete Gray
- Mix Ratio: 1:1 by volume
- Gel Time (60 Gram Mass): 14 Minutes at 75ºF/24ºC
- Tack Free Cure Time (30 mil Thin Film): 3 Hours at 75ºF/24ºC
Property | Cure Time | ASTM Standard | Units | Sample Conditioning Temperature 75°F/24°C |
Peak Compression Strength | 7 day | D695 | psi Mpa |
6,120 42.2 |
Compression Modulus | 7 day | D695 | psi Mpa |
106,400 733.6 |
Bond Strength Hardened to Hardened Concrete | 2 day
14 day |
C882 | psi Mpapsi Mpa |
1,230 8.5 1,640 |
Bond Strength Plastic to Hardened Concrete | 14 day | C882 | psi Mpa |
900 6.2 |
Water Absorption | 24 hours | D570 | % | 0.41 |
Linear Coefficient of Shrinkage | – | D2566 | % | 0.00015 |
Typical Cured Properties @ 77ºF/25ºC
Tensile Strength, psi (ASTM D 638)……………………………………………..3045
Tensile Modulus, psi (ASTM D 638)……………………………………………..308,000
Elongation at Break, % (ASTM D 638)…………………………………………..2.4
Service Temperature……………………………………………………………..approx. -20 to 140ºF
Directions
1. Clean surfaces to be bonded. Both surfaces must be clean, dry and free of oil, grease or wax. Roughen nonporous surfaces with sandpaper or emery paper for hard materials.
2. Mix equal parts by volume and mix thoroughly. When mixed properly, the adhesive is concrete gray with no streaks.
3. Cover entire area.
4. Join parts together firmly. Squeeze out excess adhesive to form a thin glue line. A larger area will require more pressure. Hold parts together with clamps, weight or tape.
5. Remove excess adhesive promptly before adhesive hardens. Scrape with a putty knife. For best results, store between 40°F/4°C and 90°F/32°C
Clean Up
Always wear appropriate protective equipment such as safety glasses and gloves. Clean uncured material with a mild solvent. Cured materials can only be removed mechanically.
The product is expected to remain stable for short term exposure to -40°F in minor repairs not including anchoring. Substrate preparation should include undercutting the perimeter. The substrate must be dry, contaminate-free. Remove any dust or loose debris prior to applying the epoxy repair. Place representative test patches or mock-up to ensure suitability.
For Technical Assistance, please click here.
Related Article Links
Why Choose EPON™ & EPIKURE™ Epoxy Resins
Choosing the Right Conformal Coatings
Polyurethane Mold Release Agents | ReleaSys™
Krytox™ is a trademark of The Chemours Company FC, LLC.
The recommendation made here with and the information set forth with respect to the performance or use of our products are believed, but not warranted to be accurate. The products discussed are sold without warranty, as to fitness or performance, express or implied and upon condition that purchasers shall make their own test to determine suitability of such products for their particular purposes. Likewise, statements concerning the possible uses of our products are not intended as recommendations to use our products in the infringement of any patent.